Aston ZAA210-L Bedienerhandbuch

Steam Bath Model Number: ZAA210-L INSTALLATION AND OWNER'S MANUALPlease carefully read these instructions before you begin to inst

Please read and follow the installation instructions and guidelines in this section.Failure to follow the recommended instructions and installation te

7. CAUTION: The flexible drain should have a level or slight grade to allow free and easy flow to the floor drain. Failure to do so can cau

Electrical RequirementsUnit must be connected by a licensed electrician for your state to a GFCIprotected circuit in order for the warranty to be vali

Install your unit according to the directions in this section in the order presented. Locate the accessory and manual box and remove the individual

WARNING: Failure to apply proper pitch or grade for drainage can cause leakingand/or flooding of the area surrounding the unit.1.After making all the

The Whirlpool tub comes equipped with a factory installed drain and overflow anoptional flexible drain hose is also provided to avoid having to move t

1.Remove and inspect all of the glass panels. If any are broken, pleasecontact your dealer or the manufacturer.NOTE: The glass panels are labeled to

3. Place the bottom aluminum rail on the floor with correct orientation up to receive the glass panel. 4. Apply a liberal bead of sealant o

Use the following steps to assemble the glass side panel on to the glass doorpanelInsert the aluminum channel on to the glass door panel based on the

1.Open and remove the acrylic back and side panel(s) and inspect fordamage.IMPORTANT: Please note the direction of the screw head. Make sure you can g

Thank you for purchasing your Aston steam shower with attached whirlpool bath.We hope that it will provide you with years of satisfying use and enjoym

3. Using a caulk gun with appropriate bathroom caulk place the tip of the caulk gun into the opening between the two panels. Run a bead o

NOTE: The acrylic wall assembly can be heavy so please use caution when liftingit and placing it onto the whirlpool bath.1.Lift and place the acrylic

3. Apply a liberal bead of sealant onto the whirlpool bath in line with the mounting screw holes. 4. Place the acrylic wall back onto the

NOTE: As with the acrylic assembly, the glass panel assembly is heavy to lift.Please use caution when lifting this assembly and use two people to lif

5. Apply an additional bead of sealant along the whirlpool bath where the glass panel assembly will sit. 6. Place the glass panel assembly bac

NOTE: The ceiling panel is large and can be an odd shape. Please use cautionwhen lifting this assembly and use two people to lift it into place.1.Lif

After you have installed and lightly assembled the cabinet walls, you can begin tofully secure all screws and bolts.Tighten the screws in the followin

If your unit includes a decorative trim panel, use the following steps to install thetrim piece.1.Using Screw Pack 6 use the M4 X 30mm screws, nuts, a

1.Remove and inspect the glass doors. If any are damaged or broken, pleasecontact your dealer or the manufacturer.2. Determine which door is the right

tube and back plastic washer on the door roller. 5. Taking one of the doors, with the two holes for the door handles located so that

WARNING: To reduce the risk of drowning, electrical shock, or injury, read thefollowing important precautions before using the unit. If you do not fu

1. The door handles are located within the accessory manual box. Remove them from the packaging and note the end with the knob on it. The

The mounting screws to mount the shower wand holder should already be inplace on the acrylic panel assembly. Remove them for this assembly.1.Assemble

1. The shower wand hose has two tapered ends. One end has an O-ring around the outside. Install this end onto the shower wand. Install the rubber g

1.Remove the showerhead from the packaging.2. Install the showerhead onto the showerhead spout located in the center ofthe unit's ceiling. If the

1.Insert the showerhead hose into one of the access holes located in theceiling of the unit.2. Install the elbow/barb fitting provided onto the shower

WARNING: Any final electrical connections must be to a GFCI protected circuitand made by a certified electrician.Based on your unit you may or may no

After completion of the electrical and plumbing connections we recommend thatyou conduct a system test to ensure all connections are working properly

Before operating this unit ensure you have read and understand all of thewarnings and safety statements in this manual. If you do not understand any o

Note: This diagram is for reference purpose only, and theactual connections may vary.37Overhead showerWaterfall SpoutBody & Neck massage jetsCold

Components38Diverter valveThe diverter valve is used to control the flow of water to the following devices: The Showerhead The b

THE FOLLOWING WARNING ONLY APPLY TO UNITS THAT ARE ACOMBINATION STEAM SHOWERS/STEAM BATH UNIT CONTAINING ANATTACHED HYDRO-MASSAGE BATHTUB1.WARNING: To

39Shower Wand1. Rotate the diverter valve to the shower wand position. Water will begin toflow.2. Set the thermostatic valve.3. When finished, rotate

Functions4018222324Body jetsBased on the typical residential water pressure and flow rates not all of the bodyjets can work at the same tim

41 i.Press the local zone button you wish to turn on based on the diagram located on the diagram located on the control panel. ii.Press the

SteamThe unit is equipped with a built-in steam generator. It is important that youunderstand how the unit operates before you use it. Read and follow

If you wish to change the length of time for the steam cycle press the “time” buttonup or down. The maximum set time is 99 minutes.If you wish to chan

2. Press the “fan” button to turn the fan on. 3. Press the “fan” button to turn the fan off.Radio TunerThe unit is equipped with an FM tuner (no

Care and Maintenance As with any other luxury item, maintenance and care are critical to the long lastingquality and enjoyment of your steam shower.

Unscrew the affected jet or showerhead and clean or soak it with a mild solutionof vinegar and water (50/50) or commercially available hard water cle

SymptomsPossible Causes SolutionsNo power to unit1. Loose powerconnections2. GFCI Breaker tripped3. Internal breaker trip4. Blown fuseMissing internal

SymptomsPossible Causes Solutionsthan the internal ambienttemperature, the timesetting must not be zero“0”7. Check the fuses onthe main control boardr

Becoming familiar with commonly used plumbing and electrical terms will help youas you use this owner's manual and when you consult the dealer re

Symptoms Possible Causes SolutionsLight not working 1. Burned out light bulb2. Loose connection1. Replace light bulb2. Repair any looseconnectionsRad

Symptoms Possible Causes Solutionslook at the check valvesto see for any obstructionor stuck valve3. If you are using shutoff valves for the supplylin

Symptoms Possible Causes Solutions3. Verify all water supplyvalves are openLeaks from Jets 1. Loose jet faces2. Loose hose1. Remove and reinstalljet f

Symptoms Possible Causes Solutions2. Check for looseconnections to the lightbulb3. Replace light bulb 52

PLEASE READ THESE WARRANTY TERMS AND CONDITIONSCAREFULLY BEFORE USING YOUR ASTON GLOBAL BATHROOMPRODUCT. BY USING THE PRODUCT, YOU ARE CONSENTING TO B

verification that the Product arrived in a good and acceptable condition);and (b) clearly notate damage on the delivery acknowledgment receipt.Failure

allow the exclusion or limitation of incidental or consequential damages, so theabove limitations or exclusions may not apply. No dealer, distributor

Customer Service877-424-9699Aston Global Inc1501 10th St Suite 150PLANO, TX 75074 If further assistance is needed, or you

NEC (National Electric Code) (USA) Universal set of standards governing proper electrical installationNeutral

Line (L1) = 110-120 VAC (Black or “Hot 1”) Line (L2) = 110-120 VAC (Red or White or “Hot 2”)

1.Light 2.Speaker 3.Handheld Shower Wand 4. Diverter Valve 5.Thermostatic Faucet 6. Mirror 7. Whirlpool Tub Spout 8.Steam Unit Drain Port9.S

SUPPLIED HARDWARE14M4x16M4x50444SCREW PACK (3)SCREW PACK (4)M4x308M4x356M4x60M4x305M5x40SCREW PACK (5)SCREW PACK (6)M4x302 7SCREW PACK (1)10SCREW PACK